Pls I need it fast , its for my homework and I can’t find it

The electric field strength inside the solenoid at a point on the axis is -7.45 x 10⁻³ V/m.

The electric field strength inside the solenoid can be found using Faraday's Law of Induction, which states that the induced electric field is proportional to the rate of change of magnetic flux.
Since the solenoid has a diameter of 5.0 cm, its radius is 2.5 cm or 0.025 m. The magnetic field inside the solenoid can be expressed as B = μ₀ * n * I, where μ₀ is the permeability of free space, n is the number of turns per unit length, and I is the current. Since the solenoid is not mentioned to have any current, we assume that there is no current and the magnetic field is solely due to the changing magnetic flux. Therefore, we can use the equation ε = -dΦ/dt to find the electric field strength, where ε is the induced electric field and dΦ/dt is the rate of change of magnetic flux.
The magnetic flux through the solenoid is given by Φ = B * A, where A is the area of the cross-section of the solenoid. Since the solenoid has a diameter of 5.0 cm, its cross-sectional area can be expressed as A = π * r² = π * (0.025 m)² = 1.96 x 10⁻³ m².
Substituting the given values into the equation, we have:
ε = -dΦ/dt = -d(B * A)/dt = -A * dB/dt
ε = -(1.96 x 10⁻³ m²) * (3.80 t/s) = -7.45 x 10⁻³ V/m
Therefore, the electric field strength inside the solenoid at a point on the axis is -7.45 x 10⁻³ V/m.

learn more about electric field here

https://brainly.com/question/15800304

#SPJ11

In a tensile force measurement using a strain gauge, the strain gauge is typically attached to the surface of the material experiencing the tensile force. The strain gauge is a resistive sensor that changes its electrical resistance in response to the deformation or strain of the material.

When a tensile force is applied to the material, it causes the material to deform. This deformation results in a change in the length and cross-sectional area of the material. The strain gauge, being bonded to the surface of the material, also experiences this deformation, which causes a change in its resistance.
The relationship between the change in resistance (∆R) and the tensile force (P) can be derived using the concept of strain and the gauge factor (GF) of the strain gauge. The gauge factor is a constant that represents the sensitivity of the strain gauge and is typically provided by the manufacturer.
The relationship is given by the equation:
∆R = GF * R * ε
Where:
∆R is the change in resistance of the strain gauge,
GF is the gauge factor of the strain gauge,
R is the initial resistance of the strain gauge,
ε is the strain experienced by the material.
To determine the change in resistance for a strain gauge installed on a beam being pulled axially by a 50 kN tensile force, additional information is required. Specifically, the length of the beam and the modulus of elasticity (E) of the material. With this information, the strain (ε) can be calculated using the equation
ε = δL / L
Where:
δL is the change in length of the beam,
L is the initial length of the beam.
Once the strain is determined, the change in resistance can be calculated using the derived relationship ∆R = GF * R * ε, where GF and R are given as 2 and 1200, respectively.

To learn more about, Strain Gauge, click here, https://brainly.com/question/32087166

#SPJ11

the momentum = m * v

m : mass

v : velocity

momentum = 1 * 50 = 50 kg.m/s

Answer:

true

Explanation:

I think true because I think

Answer:

No, they will not change.

Explanation:

we can write any vector as the sum of two vectors, one in and one in , by finding the components of the vector along the basis vectors and using the dot product formula  = ( · ) + ( · ). If the basis is orthogonal, the computation becomes simpler.

To write a vector as the sum of two vectors, one in and one in , we first need to find the components of the vector along the basis vectors and .

Let's assume that is an orthogonal basis for . This means that the dot product between any two basis vectors is zero.

Now, suppose we have a vector , and we want to write it as the sum of two vectors and . We can use the following formula:

= ( · ) + ( · )

Here, represents the component of along the vector , and represents the component of along the vector .

So, we need to find and . We can do this using the dot product:

= ·

= ·

Now, we can solve for and :

= ( · ) + ( · )

= ( · ) + ( · )

To write a vector as the sum of two vectors, one in and one in , we first need to find the components of the vector along the basis vectors and . We can use the dot product to find these components. Assuming that is an orthogonal basis for , we can use the formula  = ( · ) + ( · ) to write the vector as a sum of two vectors.

In conclusion, we can write any vector as the sum of two vectors, one in and one in , by finding the components of the vector along the basis vectors and using the dot product formula  = ( · ) + ( · ). If the basis is orthogonal, the computation becomes simpler.

To know more about vectors visit:

brainly.com/question/24256726

#SPJ11

The speed of an electron when its kinetic energy is 8 times its rest energy is approximately 0.93c, or 93% of the speed of light.

The kinetic energy of an object is given by 1/2mv^2, where m is the mass of the object and v is its velocity. The rest energy of an electron is approximately 0.511 MeV/c^2. Thus, when the kinetic energy of the electron is 8 times its rest energy, we have:
1/2mv^2 = 8(0.511 MeV/c^2)
Solving for v, we get:
v = sqrt[(2*8*0.511 MeV/c^2)/m]
The mass of an electron is approximately 9.11 x 10^-31 kg. Plugging in the values, we get:
v = sqrt[(8.176 MeV)/9.11 x 10^-31 kg]
v ≈ 2.79 x 10^8 m/s = 0.93c
Therefore, the speed of the electron is approximately 93% of the speed of light, or 0.93c.

Learn more about kinetic energy here:

https://brainly.com/question/20231254

#SPJ11

The answer to this question is adiabotic process

Answer:

The answers should be B and D

Explanation:

I hope this helps!

Based on the given information, The observation that an object floats or sinks in a liquid is influenced by the relative densities of the object and the liquid. The correct option is D)

If the object's density is higher than the liquid, it will sink, and if it is lower, it will float. However, without additional information about whether the object floated or sank in each of the four liquids, we cannot conclusively determine the density of the object. The experiment only provides information about the object's buoyancy in relation to the liquids but does not directly reveal its absolute density. Therefore the correct answer is option D).

To know more about relative densities, here

brainly.com/question/15164682

#SPJ4

--The complete Question is, "In an experiment, a student releases an object from rest in four different liquids and observes whether it floats. What can be concluded about the density of the object?"

Options:

A) The object has a lower density than all four liquids.

B) The object has a higher density than all four liquids.

C) The object has a density equal to at least one of the liquids.

D) The density of the object cannot be determined.--

Answer:

2121 newtons

Explanation:

Different masses are hung on a spring, then the different values obtained after solving are 49 N, 10 kg, and 686 N.

The fundamental force of attraction operating on all matter is recognized as gravity, also spelled gravity, in mechanics. It has no impact on identifying the interior properties of common matter because it is the weakest force known to exist in nature.

The formation and growth of planets, galaxies, and the universe are all under the influence of this long-range, cosmic force, which further determines the trajectories of objects throughout the universe and the entire universe.

As per the given information in the question,

1 kg = 9.8 N

(b)

5 kg = 5 × 9.8

5 kg = 49 N

(c)

x kg = 98 N

x = 98/9.8

x = 10 kg

(d)

70 kg = 70 × 9.8

70 kg = 686 N.

To know more about gravity:

https://brainly.com/question/4014727

#SPJ12

The lion has a kinetic energy of 5000 j, the speed of the lion is  v = 100 / \(\sqrt{M1}\)  m/s

Kinetic energy is a form of energy that an object or a particle has by reason of its motion. If work, which transfers energy, is done on an object by applying a net force, the object speeds up and thereby gains kinetic energy or Kinetic energy is the energy that an object possesses due to its motion. It is basically the energy of mass in motion. Kinetic energy can never be negative and it is a scalar quantity i.e. it provides only the magnitude and not the direction.

given

kinetic energy = 5000 J

speed = ?

since , mass is not given in the question

Let mass of lion will be = M1

kinetic energy = 1/2 * M1 * \(v^{2}\)

             5000 J = 1/2 * M1 *  \(v^{2}\)

             \(v^{2}\) = \(\sqrt{10,000 / M1}\)  m/s

              v = 100 / \(\sqrt{M1}\)  m/s

The speed of the lion =  v = 100 / \(\sqrt{M1}\)  m/s

To learn more about kinetic energy

https://brainly.com/question/12669551?referrer=searchResults

#SPJ4

Vega is a main-sequence star of spectral type A, with a mass of about 2.1 times that of the Sun. As a main-sequence star, Vega is burning hydrogen in its core to produce energy, and it will continue to do so for several billion years.

After it exhausts the hydrogen in its core, Vega will enter a new phase of its life known as the red giant phase. During this phase, Vega will expand to become a much larger star, with a radius that may be several hundred times larger than its current radius. The outer layers of Vega will cool and become less luminous, causing the star to appear redder in color.

As the red giant phase progresses, the core of Vega will contract and heat up, eventually becoming hot enough to fuse helium into heavier elements. This process will release a large amount of energy, causing the outer layers of the star to be blown away in a massive explosion known as a planetary nebula. The hot, compact core that remains will eventually cool down and become a white dwarf, the final stage of stellar evolution for stars like Vega.

So, Vega is expected to expand into a red giant star before evolving into a white dwarf.

To know more about luminous refer here

https://brainly.com/question/29564864#

#SPJ11

Answer:

distance

Explanation:

it is the distance traveled by light in one year

Answer:

nuclear fusion plants are fossil fuels, if you are asking which of the following is a fossil fuel

Explanation:

The power needed to warm the cold outside air to inside temperature in a standard 150 m2 house with an outside temperature of 0°C and an inside room temperature of 20°C is 2076.24 watts.

To calculate the power needed, we first need to calculate the amount of heat needed to warm the air. This is done using the following formula:

Heat = Mass * Specific Heat * Temperature Change

The mass of the air in the house is calculated by multiplying the volume of the house by the density of air. The volume of the house is 150 m2 * 3.28 m/m2 = 486 m3. The density of air at 0°C is 1.225 kg/m3.

The specific heat of air is 1.013 kJ/kg·K. The temperature change is 20°C - 0°C = 20°C.

So, the amount of heat needed to warm the air is 486 m3 * 1.225 kg/m3 * 1.013 kJ/kg·K * 20°C = 9962 kJ.

The power needed to warm the air is then calculated by dividing the amount of heat needed by the time it takes to change the air, which is 5 hours * 3600 seconds/hour = 18000 seconds.

So, the power needed is 9962 kJ / 18000 seconds = 0.554 kJ/second = 2076.24 watts.

To know more about power, click here:-

https://brainly.com/question/30497148

#SPJ11

In an inviscid fluid, the lift generated on an aerodynamic object would be determined by the shape of the object and its angle of attack.

The lift is created by the difference in air pressure between the upper and lower surfaces of the object, as the fluid flows around it. This pressure difference creates a force that lifts the object upward. However, in a real-world scenario, viscous effects would come into play, which can affect the lift generated. the values for circulation, fluid density, and freestream velocity to determine the lift generated on the aerodynamic object in the inviscid fluid. In summary, to determine the lift generated on an aerodynamic object in an inviscid fluid, you must first calculate the circulation around the object and then apply the Kutta-Joukowski theorem.

Learn more about inviscid fluid at  brainly.com/question/17010211

#SPJ11

Doubling the kinetic energy of a car does not change its momentum. Momentum is determined solely by the mass and velocity of the object, independent of its kinetic energy.

Kinetic energy and momentum are two different physical quantities that describe the motion of an object. Kinetic energy depends on the mass and velocity of an object, while momentum depends only on the mass and velocity.

When the kinetic energy of a car is doubled, it means that the car's velocity is increased while its mass remains the same. However, momentum is the product of mass and velocity, so if the mass remains constant, any change in kinetic energy does not directly affect momentum.

Mathematically, the formula for kinetic energy is KE = (1/2)mv^2, where KE represents kinetic energy, m represents mass, and v represents velocity. On the other hand, momentum is given by the formula p = mv, where p represents momentum. As we can see, kinetic energy involves velocity squared, while momentum only involves velocity.

Learn more about velocity here:

https://brainly.com/question/30559316

#SPJ11

Answer: A. Reference point

Explanation: A reference point is usually the start of a location, and if it's a starting point, then it will be 0.

Have a nice day. :)

For the given swimming pool A) the absolute pressure on the bottom of the swimming pool is 117,640 N/m^2; B) the total force on the bottom of the swimming pool is 35,653,960 N; C) the pressure against the side of the pool near the bottom is  17,640 N/m^2.

The dimensions of a swimming pool are 34.0 m by 9.5 m, and its uniform depth is 1.8 m. The atmospheric pressure is 1.013×10^5 N/m2.

A) Absolute pressure on the bottom of the swimming pool is given by the formula:

P = atmospheric pressure + ρgh

Here, ρ is the density of the fluid, g is the acceleration due to gravity, and h is the depth of the swimming pool.

Let's use the values given to calculate absolute pressure on the bottom of the swimming pool:

P = 1.013 × 10^5 + (1000 × 9.8 × 1.8)

P = 1.013 × 10^5 + 17640 = 117,640 N/m^2

Therefore, the absolute pressure on the bottom is 117,640 N/m^2

B) The total force on the bottom of the swimming pool is calculated using the formula:

F = pA

Here, p is the pressure on the bottom of the swimming pool, and A is the area of the bottom of the swimming pool.

Let's use the values given to calculate the total force on the bottom of the swimming pool:

F = 117,640 × 34 × 9.5

F = 35,653,960 N

Therefore, the total force on the bottom is 35,653,960 N.

3. Pressure against the side of the pool near the bottom is equal to the hydrostatic pressure, which is given by the formula:

P = ρgh

Here, ρ is the density of the fluid, g is the acceleration due to gravity, and h is the depth of the swimming pool.

Let's use the values given to calculate the pressure against the side of the pool near the bottom:

P = 1000 × 9.8 × 1.8P = 17,640 N/m^2

Therefore, the pressure against the side of the pool near the bottom is 17,640 N/m^2.

Learn more about Absolute pressure:

https://brainly.com/question/17200230

#SPJ11

Disequilibrium occurs when the quantity of supply does not equal the quantity of demand.

The market is experiencing a disequilibrium when the market price is above or below the equilibrium price. Whenever markets experience imbalances—it creates disequilibrium prices, surpluses, and shortages—market forces drive prices toward equilibrium.

A surplus exists when the price is above equilibrium, which encourages sellers to lower their prices to eliminate the surplus.

A shortage will exist at any price below equilibrium, which leads to the price of the good increasing.

For example, imagine the price of dragon repellent is currently $6 per can. People only want to buy 400 cans of dragon repellent, but the sellers are willing to sell 600 cans at that price. This creates a surplus because there are unsold units. Sellers will lower their prices to attract buyers for their unsold cans of dragon repellant.

learn more about disequilibrium market:

https://brainly.com/question/13985127

#SPJ4

A) Storm surge causes the most devastating damage in the coastal zone during a strong hurricane.

Storm surge refers to the abnormal rise of water levels along the coast caused by a combination of low atmospheric pressure and strong onshore winds associated with a hurricane. It results in the flooding of coastal areas, including low-lying regions and inland waterways. The surge of water can cause widespread destruction to infrastructure, homes, and natural habitats, leading to loss of life and severe property damage. The force and volume of water carried by the storm surge can overwhelm coastal defenses, erode beaches, and inundate inland areas.

While strong winds, torrential rains, and lightning are all significant factors during a hurricane, storm surge is typically the most destructive element in the coastal zone due to its ability to cause widespread and severe flooding.

To learn more about strong hurricane visit: brainly.com/question/18950883

#SPJ11

To calculate the temperature of the air after it has doubled in volume, we need to use the Ideal Gas Law which states that PV = nRT, where P is pressure, V is volume, n is the number of moles of gas, R is the gas constant, and T is temperature. Since we know that the pressure is constant and the volume has doubled.

(P)(2V) = (n)(R)(T2) where T2 is the temperature after the air has doubled in volume. We can simplify this equation by dividing both sides by PV and using the fact that PV = nRT, which gives: 2 = (T2 / T) where T is the initial temperature of the air. Solving for T2, we get: T2 = 2T Substituting the initial temperature T = 300 K, we get: T2 = 2(300 K) = 600 K To calculate the temperature of the air after it has doubled in volume, we will use the following ideal gas law formula:
PV = nRT

where P is pressure, V is volume, n is the number of moles of gas, R is the ideal gas constant, and T is temperature. Since the pressure is constant, we can set up the following proportion: V1/T1 = V2/T Given the initial conditions: V1 = 1 L (initial volume) T1 = 300 K (initial temperature) V2 = 2 L (final volume, since the volume doubled) We want to find T2 (the final temperature). To do this, plug the values into the proportion: (1 L)/(300 K) = (2 L)/T2 Now, solve for T2: T2 = (2 L) * (300 K) / (1 L) T2 = 600 K The temperature of the air after it has doubled in volume is 600 K.

To know more about temperature visit:

https://brainly.in/question/3336671

#SPJ11

The temperature of the air after it has doubled in volume is 600 K.

Given that air is an ideal gas, we can use the ideal gas law, which states that PV = nRT, where P is pressure, V is volume, n is the amount of gas, R is the ideal gas constant, and T is temperature. In this case, we have the initial state and final state of the gas, and we want to calculate the final temperature.
Initial state:
P1 = 1 atm
V1 = 1 L
T1 = 300 K
Final state:
P2 = 1 atm (constant pressure)
V2 = 2 L (doubled volume)
T2 = ? (we need to find this)
Since the pressure is constant, we can set up a ratio using the initial and final states:
(V1/T1) = (V2/T2)
Plugging in the known values:
(1 L / 300 K) = (2 L / T2)
Now we can solve for T2:
T2 = (2 L * 300 K) / 1 L
T2 = 600 K

So, the temperature of the air after it has doubled in volume is 600 K.

Learn more about temperature click here:

https://brainly.com/question/24746268

#SPJ11

Pption d. flow does not independently influence the speed of water in a stream. Instead, it is an outcome determined by the combined effects of gradient, discharge, and channel geometry.

The flow itself, or the rate at which water moves in a stream, is not an independent factor that influences the speed of water in a stream. Instead, it is a result of other factors such as gradient, discharge, and channel geometry.

a. Gradient: The gradient, or slope, of the stream affects the speed of water. Steeper gradients generally lead to faster-flowing water.

b. Discharge: The discharge of a stream, which refers to the volume of water passing through a given point in a specified amount of time, directly affects the speed of water. Higher discharge results in faster flow.

c. Channel geometry: The shape and dimensions of the stream channel also influence the speed of water. Wider and deeper channels tend to have slower flow, while narrower and shallower channels often lead to faster flow.

Therefore, option d. flow does not independently influence the speed of water in a stream. Instead, it is an outcome determined by the combined effects of gradient, discharge, and channel geometry.

To learn more about gradient, click here:

https://brainly.com/question/28016665

#SPJ11

Answer:

potential energy

the cat is at reast not moving the energy inside of it could move tho

Answer:

The pencil will appear wider and bent

Explanation:

no explanation

The binding energy per nucleon for 10747Ag is 7.47 MeV, and for 10947Ag, it is 7.39 MeV.

The binding energy per nucleon is the amount of energy required to completely separate the nucleus of an atom into its individual nucleons. It is a measure of the stability of the nucleus, and the higher the binding energy per nucleon, the more stable the nucleus.

To calculate the binding energy per nucleon for each isotope of silver, we need to first calculate the total binding energy of each isotope. The total binding energy is the sum of the binding energies of all the nucleons in the nucleus. The binding energy per nucleon is then calculated by dividing the total binding energy by the number of nucleons.

Using the given atomic masses and isotopic abundances, we can calculate the mass of each isotope and the number of nucleons in each isotope. The number of neutrons in each isotope can be calculated by subtracting the atomic number (47) from the mass number (106 or 108). The binding energy of each isotope can then be calculated using the Einstein's famous equation E=mc², and the binding energy per nucleon can be calculated by dividing the binding energy by the number of nucleons.

After these calculations, we find that the binding energy per nucleon for 10747Ag is 7.47 MeV, and for 10947Ag, it is 7.39 MeV. This indicates that 10747Ag is more stable than 10947Ag, as it has a higher binding energy per nucleon.

Learn more about binding energy here:

brainly.com/question/10095561

#SPJ11